Descrizione

For development, precompliance and conformance testing of mobile phones
Key Facts
  • Platform for RF tests according to 3GPP TS 51.010-1 and TS 34.121-1
  • Freely configurable RF test methods for development
  • Supports GSM Ph2/Ph2+, GPRS, EDGE and VAMOS
  • Supports WCDMA R99-R7
  • Open interfaces for easy integration into individual lab concepts
  • Control of custom equipment
  • Full remote access
  • Online measurement accuracy control

Brief Description The R&S®TS895x family consists of a full range of highly configurable RF test systems for user equipment (UE) and mobile phones. The R&S®TS8950 represents the top end of the third generation of RF test systems from Rohde & Schwarz that fulfills all requirements for RF conformance tests on 2G, 2.5G and 3G devices. Customized and standard solutions for development and precompliance testing are available with the R&S®TS8955x test solutions, i.e. the R&S®TS8955G, R&S®TS8955W and R&S®TS8955GW in various configurations depending on the required functionalities. The R&S®TS8955 uses the same application software as the R&S®TS8950. The R&S®TS8950 systems feature fully automatic path calibration routines that run with minimum manual intervention and without the need for any external equipment.
Features & Benefits
  • Hardware components R&S®TS8950 hardware components at a glance:
    • R&S®CRTU-G, R&S®CRTU-S or R&S®CRTU-W, R&S®CRTU-M: for GSM / WCDMA base station simulation
    • R&S®ABFS: fading simulator for simulation of GSM base station signal propagation
    • R&S®SMU200A: fading simulator for simulation of WCDMA base station signal propagation
    • R&S®FSU26: state-of-the-art high dynamic range spectrum analyzer for transmitter measurements and internal RF calibration
    • R&S®SMU200A: dual IQ vector signal generator for generation of modulated interferers in GSM/WCDMA
    • R&S®SMP02: microwave generator for generation of wideband interferers and for internal RF calibration
    • R&S®NRVD: power meter as internal reference for RF calibration
    • R&S®NGSM32: programmable DC power supply for automated test runs under extreme test conditions (low/high supply voltage)
    • R&S®SSCUGW: mainframe signal switching and conditioning unit for GSM and WCDMA
    • R&S®ASCUxx: advanced signal conditioning units for band-specific signal conditioning
    • R&S®TS-TMB: temperature sensors logging the temperature at the device under test and/or test environment
    • Rubidium frequency standard and signal distributor or optimum timing stability and synchronism
    • 19 system controller with Ethernet, RS-232-C and USB interfaces (controller is equipped with two hard disks to support RAID level software features under Windows 2000)
    • Double or triple 19 rack with integrated fans
  • Software R&S®TS8950 control center:
    • Application editor for defining new test cases and modifying test parameters
    • Sequence editor for arranging test sequences for automated test run
    • Report analyzer for generating graphical and textual report of test results, extensive offline or online analysis against different parameters varied during the test run
    • Calibration wizard for configuring calibration setups
    • DUT editor for defining DUT characteristics (power class, multislot class, supply voltage, etc)
    • SIM editor for configuring IMSI, TMSI and other parameters
    • Operator editor for entering information about system operator to be logged with test report
    • System configuration editor for controlling the devices used by the system
    • Version manager for easy handling of multiple software versions
    Operating software:
    • Operating system: Windows XP Embedded
    • Programming environment: LabWindows CVI
  • Test Applications With R&S®TS8950G: RF tests for
    • GSM, GPRS, AMR, DARP and EGPRS in accordance with 3G TS51.010-1 (formerly GSM11.10)
    • Section 12
    • Section 13
    • Section 14
    • Section 16
    • Section 18
    • Section 21
    • Section 22
    With R&S®TS8950W: RF tests for
    • WCDMA FDD1, 2, 5, 6 in accordance with 3G TS34.121 , HSDPA, Rel.5
    • Section 5
    • Section 6
    • Section 7
    • Section 9
    Remark: Radio resource management tests, section 8, are available in a separate test setup or as an extension to the R&S®TS8950W or R&S®TS8950GW. All test cases are implemented based on test methods. The test methods are generic test applications with parameter sets that can be edited via an intuitive Windows user interface. Only a few test methods are required to cover the full set of RF test cases. This approach allows a maximum of consistency between different tests and the ability to change tests or even write completely new complex RF tests with no programming effort at all.
  • Automatic path calibration The R&S®TS8950 systems feature fully automatic path calibration routines that run with minimum manual intervention and without the need for any external equipment. This is not limited to conformance tests only. Optimum measurement accuracy is also maintained for tests that have been changed by the operator and even for completely new customer defined tests using the existing test methods.
  • R&S®TS8955 RX bench top The minimum configuration for receiver tests allows to run performance and in-band receiver test cases. The path calibration can be streamlined to the content of specific test campaigns. Calibration data is then only gathered for the tests of interest – so more time can be spent on testing rather than on calibration.
    • R&S®CMU200: universal radio communication tester CMU200 for GSM / WCDMA base station simulation, testing and calibration
    • Fading simulator R&S®ABFS: fading simulator for simulation of GSM base station signal propagation or
    • Fading simulator R&S®SMU200A: fading simulator for simulation of GSM / WCDMA base station signal propagation
    • Modulated interferer R&S®SMU200A: dual signal generator for generation of modulated interferers in GSM / WCDMA (also HSDPA) or
    • Modulated interferer R&S®SMIQ03B: vector signal generator for generation of modulated interferers in GSM / WCDMA
    • System Controller to control the R&S® instruments e.g. R&S®PSL3 industrial controller
  • R&S®TS8955 TX bench top This configuration allows to run spectrum and modulation tests cases.
    • R&S®CMU200: universal radio communication tester CMU200 for GSM / WCDMA base station simulation and testing and calibration
    • Spectrum Analyzer R&S®FSU26: state-of-the-art high dynamic range spectrum analyzer for transmitter measurements or
    • Spectrum Analyzer R&S®FSP3: spectrum analyzer for high speed in transmitter measurements
    • System Controller to control the R&S® instruments e.g. R&S®PSL3 industrial controller
  • R&S®TS8955 RX/TX bench top This configuration allows to run performance and in-band receiver test cases as well as spectrum and modulation tests cases.
    • Fading simulator R&S®SMU200A: fading simulator for simulation of GSM / WCDMA base station signal propagation
    • Modulated interferer R&S®SMIQ03B: vector signal generator for generation of modulated interferers in GSM / WCDMA
    • Spectrum Analyzer R&S®FSP3: spectrum analyzer for high speed in transmitter measurements
  • R&S®TS8955 Rack The top end of the R&S®TS8955 configurations also allows for spurious, blocking and intermodulation test cases.
    • R&S®CMU200: universal radio communication tester R&S®CMU200 for GSM / WCDMA base station simulation and testing and calibration
    • R&S®SMU200A: fading simulator for simulation of WCDMA base station signal propagation
    • R&S®FSU26: state-of-the-art high dynamic range spectrum analyzer for transmitter measurements and internal RF calibration
    • R&S®TS-TMB: temperature sensors logging the temperature at the device under test and/or test environment
    • R&S®SMU200A: dual IQ vector signal generator for generation of modulated interferers in GSM/WCDMA
    • R&S®SMP02: microwave generator for generation of wideband interferers and for internal RF calibration
    • R&S®NRVD: power meter as internal reference for RF calibration
    • R&S®NGSM32: programmable DC power supply for automated test runs under extreme test conditions (low/high supply voltage)
    • R&S®SSCU-55: mainframe signal switching and conditioning unit for GSM and WCDMA
    • R&S® Filter boxes: band-specific signal conditioning
    • R&S®PSL3: 19 system controller with Ethernet, RS-232-C and USB interfaces (controller is equipped with two hard disks to support RAID level software features under Windows 2000)
  • Test Applications With R&S®TS8955G: RF tests for
    • GSM, GPRS, AMR, DARP and EGPRS in accordance with 3G TS51.010-1
    • Section 12
    • Section 13
    • Section 14
    • Section 21
    With R&S®TS8955W: RF tests for
    • WCDMA FDD1, 2, 5, 6 in accordance with 3G TS34.121 , HSDPA, Rel.5
    • Section 5
    • Section 6
    • Section 7
''